| 當前位置：首頁->方案設計 |
|
| MAXREFDES79#四端口IO－Link Master參考設計 |
|
|
| 文章來源： 更新時間：2015/5/18 9:33:00 |
在線咨詢： |
| |
Maxim公司的四端口IO-Link Master參考設計MAXREFDES79#包括四個IO-Link Master收發器(MAX14824),降壓轉換器(MAX15062與MAX17552), STM32F4 ARM Cortex M4微控制器(MCU)和USB連接器,具有靈活和高度集成度,加快產品上市和大大降低IO-Link Master和傳感器開發時間,主要用于控制和自動化, IO-Link傳感器和激勵器.本文介紹了IO-Link Master收發器MAX14824主要特性,功能框圖和應用電路,以及參考設計MAXREFDES79#主要特性,框圖,電路圖和材料清單.
The MAX14824 is an IO-Link master interface that integrates an IO-Link physical layer transceiver with an auxiliary digital input and two linear regulators. High port count IO-Link master applications are supported through in-band SPI addressing, and the 12MHz SPI interface minimizes host controller access times. In-band addressing and selectable SPI addresses enable cascading up to 16 devices.
The device supports all the IO-Link data rates and features slew-rate-controlled drivers to reduce EMI. The driver is guaranteed to drive up to 300mA (min) load currents. Internal wake-up circuitry automatically determines the correct wake-up polarity, allowing for the use of simple UARTs for wake-up pulse generation.
The MAX14824 is available in a 4mm x 4mm, 24-pin TQFN package with exposed pad, and operates over the extended -40NC to +105NC temperature range.
MAX14824主要特性:
IO-Link v.1.0 and v.1.1 Physical Layer Compliant
Supports COM1, COM2, and COM3 Data Rates
Push-Pull, High-Side, or Low-Side Outputs
300mA C/Q Output Drive
1μF C/Q Load Drive Capability
Generates 500mA Wake-Up Pulse
Automatic Wake-Up Pulse Polarity
Auxiliary Digital Input
5V and 3.3V Linear Regulators
SPI Interface for Configuration and Monitoring
SPI-Based Chip Addressing
EMI Emission Control Through Slew-Controlled Driver
Reverse-Polarity Protection on DI
Short-Circuit Protection on C/Q
High Temperature Warning and Thermal Shutdown
Extensive Fault Monitoring and Reporting
-40NC to +105NC Operating Temperature Range
4mm x 4mm TQFN Package
MAX14824應用:
IO-Link Master Controllers
PLC Fieldbus Gateways
High Port Count IO-Link Masters
24V Digital Inputs and Outputs
圖1. MAX14824功能框圖
圖2. MAX14824應用框圖
圖3. 采用外接電源的MAX14824電路圖
圖4.四個MAX14824應用電路圖
參考設計MAXREFDES79#
The MAXREFDES79# is the world’s first public and fully IO-Link®-compliant, 4-port IO-Link master reference design. This design uses TEConcept’s IO-Link master stack and is both an IO-Link master reference design as well as an IO-Link sensor/actuator development and test system. Four IO-Link ports allow for simultaneous testing of four different sensors (or actuators). Green and RGB LEDs located on the side of the cylindrical enclosure provide power and communication status, respectively. The reference design has four robust female M12 connectors, the most common connector used for IO-Link, and ships with two black IO-Link cables to quickly connect to IO-Link compatible sensors and actuators. An AC-to-DC (24VDC/1A) power-supply cube is capable of providing greater than 200mA simultaneously to each port and greater than four times that amount if the other ports are unused. A Micro-USB connector underneath the enclosure allows for quick connectivity to a Windows® PC. The easy-to-use TEConcept Control Tool (CT) GUI software with IODD file import capability makes the MAREFDES79# a must-have for any company or engineer serious about developing IO-Link products.
The MAXREFDES79# IO-Link master consists of 4 main blocks: four IO-Link master transceivers, step-down converters, microcontroller, and USB connection as shown in Figure 6. The MAX14824 IO-Link master transceiver is IO-Link version 1.1/1.0 physical layer compliant with highly integrated 5V and 3.3V linear regulators, configurable outputs (push-pull, high side or low side), auxiliary digital input, 300mA C/Q output drive, and reverse-polarity/short-circuit protection, all in a small 4mm x 4mm, industrial-friendly TQFN package.
The MAX15062B is a high-voltage, synchronous step-down converter that efficiently converts 24V to 5V in a tiny 2mm x 2mm, 8-pin TDFN package. The circuit defaults to PWM operation to maintain a constant frequency during all operating loads. Removing resistor R502 will put the MAX15062B into PFM mode. This reference design features optimal efficiency with PWM operation, selecting PFM mode will not provide any benefit.
Rather than use a linear regulator to drop 5V to 3.3V, the MAX17552 synchronous step-down converter efficiently converts 5V to 3.3V using a small 3mm x 2mm, 10-pin TDFN package. The MAX17552 circuit is optimized for the smallest component size and a lower input voltage range allowing the use of a 2.95mm x 2.95mm inductor instead of a 4.8mm x 4.8mm inductor. Placing the MAX17552 in series with the MAX15062B allows the MAX17552 to utilize the MAX15062B’s larger input range (up to 60V) while using the smaller inductor. The architecture uses an additional 10mW. If power efficiency is the highest priority in your design, remove resistor R503 to select PFM mode on the MAX17552 to save approximately 3mW of power. The frequency will no longer be fixed in that case.
An STM32F4 ARM Cortex M4 microcontroller in a 10mm x 10mm, 64-pin LQFP package provides system control. A universal serial bus (USB) port was implemented using the STM32F4’s internal USB peripheral and STMicroelectronic’s VCP driver.
For protection, the MAXREFDES79# features both Schottky and SMA transient voltage suppressor (TVS) diodes at the IO-Link interface. At the power-supply input, a bidirectional SMC TVS diode clamps over- and undervoltages and a Schottky diode provides reverse-polarity protection.
參考設計MAXREFDES79#主要特性:
Fully IO-Link version 1.1 compliant (downloadable test report)
TEConcept IO-Link master stack
Easy TEConcept TC tool
4 IO-Link ports
Power and status LEDs
User-friendly enclosure
Ships with all cables needed
Field update programmable
Competitive Advantages
World’s first IO-Link master reference design
Simultaneous 4-port operation
Low cost
Easy-to-use GUI
IODD import
參考設計MAXREFDES79#應用:
Control and automation
IO-Link sensors
IO-Link actuators
圖5.參考設計MAXREFDES79#元件外形圖
參圖6.參考設計MAXREFDES79#框圖
圖7.參考設計MAXREFDES79#系統運行連接圖
圖8.參考設計MAXREFDES79#電路圖(1)
圖9.參考設計MAXREFDES79#電路圖(2)
圖10.參考設計MAXREFDES79#電路圖(3)
圖11.參考設計MAXREFDES79#電路圖(4)
參考設計MAXREFDES79#材料清單:
 |
| |
|
|
|
|
|
| |
|
| |
|
|
